5133756/02INSTALLER: Please leave this guide with the ownerModel 541ROOM SEALED RADIANT / CONVECTORGAS FIREFitted with one of the following fascia.Cam
4. APPLIANCE AND RECESS DIMENSIONSThis appliance must not be recessed into a combustible wall.INSTALLER GUIDEFigure 1. Appliance dimensions and cleara
5. GENERAL INSTALLATION REQUIREMENTS5.1 Regulations, Standards and Law.The installation must be in accordance with this guide.For the user’s protectio
Where no specific instructions are given, reference should be made to the relevantBritish Standard Code of Practice.5.1.1 Considerations for timber fr
5.5.3 Combustible cladding.If the fire is to be fitted against a wall withcombustible cladding, the cladding must beremoved from the area shown in fig
5.8 Fireplace clearances.The minimum height from the base of the fire to the underside of any shelf made fromwood or other combustible materials is as
fixing template.c) Recessed into a builder’s opening or cavity of a non- combustible wall. Thecavity can be elevated. The minimum cavity size is shown
*In addition, the terminal should not be nearer than 300mm to an opening in thebuilding fabric formed for the purpose of accommodating a built-in elem
6. UNPACKING AND PRELIMINARY CHECKS6.1 Unpacking.1 Main fire assembly with fascia.1 Ceramic fuel effect (Packed in the fire).1 Nut & olive for 8mm
6.2 Appliance disassembly.Fascia removal (See figure 7). Remove the two screws securing the bottom of thefascia to the sides of the convection box.
6.3 Preliminary checks.Check ignition spark (See figure 9).The pilot burner and electrode unit is at the leftfront corner of the burner.Push in the ri
© Baxi Heating U.K. Limited 2009.All rights reserved. No part of this publication may be reproduced in any material form(including photocopying), stor
8. WALL PREPARATION8.1 Select appliance position.The flue must be installed so that it is at right angles to the back panel of the fire allround the f
structure above is secure and safe. Make the opening below the lintel by removing the masonry and clearing debris. Ifthe cavity has loose fill (e.g.
Ask for Valor Fires part no. 0591221. The insulating sheet can be used to seal theannular gap between the flue unit and the inner leaf sleeve (See sec
non-combustible sleeve 203mm (8in.) diameter will be required round the flue (Seefigure 12). Cut a hole through the inner leaf to accommodate a non-c
8.6 Prepare appliance fixing holes.8.6.1 Screwing case to wall. Recheck the position of the screw fixing holesrelative to the flue hole. Drill the f
Figure 15. Flue unit installation - Timber framed building. INSTALLER GUIDEFigure 14. Flue unit installation - Brick etc. building© Baxi Heating U.K.
9.2 Fitting to wall. Fit the flue tubes firmly over thespigots at the rear of the fire. Make surethat the seam on the flue tube is not atthe bottom.
9.3 Fitting the terminal guard. Fold the terminal guard as shown in figure 17. Place the guard centrally over the flue terminal. Holding the guard
11. CERAMIC COALS INSTALLATIONThis section is for models supplied with a ‘Coal’ fuel effect only. For ‘Pebble fuel effect’ see section 12The ceramic f
3. Hold coal ‘B’ upright with thearrow pointing to the top.Locate coal ‘B’ as shown infigure 20.4. Hold coal ‘C’ upright withthe arrow pointing to the
Page 3Safety First.Valor Fires fires are CE Approved and designed to meet the appropriate BritishStandards and Safety Marks.Quality and Excellence.All
12. CERAMIC PEBBLES INSTALLATIONThis section is for models supplied with a ‘Pebble’ fuel effect only. For ‘Coal fuel effect’ see section 11.The ceram
3. Hold pebble ‘B’ upright withthe arrow pointing to the top.Locate pebble ‘B’ as shown infigure 26.4. Hold pebble ‘C’ uprightwith the arrow pointing
13. WINDOW FITTINGFitting the window. Locate the channel at the top of the window over the top of the firebox opening. Refit the three spring loaded
The flame height control does not have to be re-set every time the fire is lit. It can bekept at any position enabling the customer to use the right h
15. FASCIA FITTINGIf you have not done so already complete the information on the last pages ofthis guide. Remove any protective film from the fascia
16. FINAL REVIEW1. COMPLETE THE INFORMATION IN THE WARRANTY AND SERVICE SECTIONOF THE OWNER GUIDE (See last pages of the OWNER guide).2. Recheck the p
17. SERVICING & PARTS REPLACEMENT Always turn off the gas and allow the appliance to cool completely beforecommencing any servicing. (The inlet ‘
clear the slots in the convection box hood and then lift clear (See figure 35).17.2 To remove window unit. Remove the fascia (See section 17.1). Uns
17.5 To remove the burner from the burner module. Remove the complete burner module as in section 17.4. Support the injector elbow and unscrew the
17.8 To remove the gas valve. Remove the complete burner moduleas in section 17.4 Remove the electrode lead at the pilot.Do this by holding the lead
INSTALLER GUIDEFOR OWNER GUIDE SEE PAGES 40 TO 51INSTALLER GUIDE© Baxi Heating U.K. Limited 2009.Page 4
OWNER GUIDEOWNER GUIDEFOR WARRANTY AND SERVICE INFORMATIONSEE PAGES 47 TO 51© Baxi Heating U.K. Limited 2009.Page 40
CONTENTSSection Heading PageSAFETY 42APPLIANCE DIMENSIONS 44GAS CONSUMPTION 45OPERATING YOUR FIRE 45To light the pilot. 46To light the main burner.
SAFETYDo have the fire installed by a competent person. In the United Kingdom, installationmust be in accordance with the latest edition of the Gas Sa
applicable standards, it is a heating appliance and certain parts of its surface willbecome hot.Do wait six minutes before attempting to relight if th
APPLIANCE DIMENSIONSOWNER GUIDEFigure 2. Appliance dimensions and clearances (Fire dimensions are subject tomanufacturing deviation). Fascia may diffe
GAS CONSUMPTIONModel 541Has a maximum natural gas input of 3.65kW (Gross)Has a maximum natural gas output of 2.8kWHas a minimum natural gas input of
To light the pilot. Push in the right control knob (the pilot lighting knob) and, while keeping itdepressed, turn anticlockwise through the ignition
MAINTENANCERegular maintenance.In order to achieve and maintain high levels of personal safety and performanceefficiency it is essential that the flue
to Friday 8am – 6pm, weekends and Bank Holidays 8.30am – 2pm, excludingChristmas Day and New Years day.When calling heateam, it would be helpful if yo
OWNER GUIDE© Baxi Heating U.K. Limited 2009.Page 49
CONTENTSSection Heading PageINSTALLER GUIDE 4 - 39OWNER GUIDE 40 - 511. SAFETY 72. APPLIANCE DATA AND EFFICIENCY 82.1 General information. 82.2 Ef
OWNER GUIDEInstaller Details (Block Capitals)Installer NameGas Safe Register or CorgiRegistration Number.Company Name.Company AddressCompany Telephone
Brand (Please tick)Baxi Valor Wonderfire Other...D D M M Y YDate of InstallationFascia code - Can be found close to the inform
© Baxi Heating U.K. Limited 2009.
Section Heading Page9. FLUE AND TERMINAL INSTALLATION 249.1 Cutting flue to size. 249.2 Fitting to wall. 269.3 Fitting the terminal guard. 2710. G
1. SAFETYInstallerBefore continuing any further with the installation of this appliance please read thefollowing guide to manual handling: The approx
as a stable, non-reactive hazardous waste and may be disposed at a landfilllicensed to accept such waste. Protective clothing is not required whenhand
2.2 Efficiency.The efficiency of this appliance has been measured as specified in BS EN 613 andthe result is as below:ModelEfficiency % (Gross)541 76T
Commentaires sur ces manuels